Lọc theo danh mục
  • Năm xuất bản
    Xem thêm
  • Lĩnh vực
liên kết website
Lượt truy cập
 Lượt truy cập :  24,065,419
  • Công bố khoa học và công nghệ Việt Nam

Các hệ thống và kỹ thuật truyền thông

Đặng Văn Ngọc(1), Nguyễn Duy Minh, Hoàng Thị Thương

Giải pháp xây dựng thiết bị truyền thông không dây cho PLC sử dụng chuẩn ZigBee

A solution to build wireless communication device for plc using ZigBee standard

Khoa học và Công nghệ - Đại học Thái Nguyên

2020

9

134-140

1859-2171

Trong các nhà máy sản xuất công nghiệp ngày nay, hệ thống giám sát và điều khiển thông thường có dây đòi hỏi phải đào rãnh để đặt dây mới, sửa chữa hoặc thay thế dây cáp cũ có thể cực kỳ tốn kém, do khả năng mở rộng thấp và tỷ lệ thất bại cao của các đầu nối. Bài báo này cung cấp một giải pháp xây dựng thiết bị truyền thông không dây cho bộ điều khiển logic lập trình (PLC) sử dụng chuẩn ZigBee. Một giải pháp phần cứng của thiết bị đã được thực hiện, sử dụng PLC ghép nối với bộ chuyển đổi tín hiệu theo chuẩn Ethernet và mô-đun truyền thông không dây XBee S2. Qua đó tiến hành xây dựng một mạng không dây bao gồm ba loại thiết bị Gateway; Router; End device. Hiệu năng của mạng đã được đánh giá qua các thông số như sau Khả năng mở rộng mạng, độ tin cậy, tính linh hoạt, khả năng định tuyến mạng, tỷ lệ truyền nhận gói tin của toàn mạng. Kết quả cho thấy bộ truyền thông không dây cho PLC có khoảng cách truyền là 55.5m và 26.05m, tỷ lệ truyền nhận gói tin là 98.4% và 84.2% tương ứng trong môi trường không vật cản và có vật cản. Mô hình mạng không dây thực nghiệm thực hiện được chức năng tự định tuyến khi liên kết đường truyền bị hỏng và mở rộng mạng linh hoạt.

In today's industrial production plants, conventional wired monitoring and control systems that require trenching to place new wires, repairing or replacing old cables can be extremely costly, due to the possibility of low expansion and high failure rate of connectors. This paper provides a wireless communication device building solution for a programmable logic controller (PLC) using the ZigBee standard. A hardware solution of the equipment was implemented, using a PLC paired with an Ethernet standard converter and XBee S2 wireless communication module. Thereby building a wireless network including three types of devices Gateway; Router; End device. Network performance has been assessed through the following parameters Network scalability, reliability, flexibility, network routing, and packet transmission rate of the entire network. The results show that the wireless communication unit for PLC has transmission distance of 55.5m and 26.05m, packet transmission rate is 98.4% and 84.2% respectively in an obstacle-free and obstructive environment. The experimental wireless network model performs self-routing when link failure and flexible network expansion.

TTKHCNQG, CTv 178

  • [1] V. N. Dang (2017), An implementation of wireless sensor nodes using zigbee technology,TNU - Journal of Science and Technology, vol. 166, no. 4, pp. 53-60, 2017
  • [2] V. N. Dang; D. M. Nguyen; V. H. Ninh (2019), Construction of the input signal transducer of the plc using ethernet,TNU - Journal of Science and Technology, vol. 204, no. 11, pp. 173-179, 2019
  • [3] S. Monk (2016), Programming Arduino Getting Started with Sketches,McGraw-Hill Education, 2016
  • [4] Q. H. Pham; T. H. Nguyen (2019), Microcontroller And Arduino Application For Self-Learners,Hanoi University of Science and Technology, 2019.
  • [5] N. B. Le; Q. H. Pham (2016), Scada PLC Programming Industrial Communication Network,Hanoi University of Science and Technology, 2016
  • [6] (1998), Industrial Communication network,
  • [7] N. Salman; I. Rasool; A. H. Kemp, (2010), Overview of the IEEE 802.15.4 standards family for Low Rate Wireless Personal Area Networks,IEEE 7th International Symposium on Wireless Communication Systems, United Kingdom, September 19-22, 2010, pp. 701-705.
  • [8] S. Safaric; K. Malaric (2006), ZigBee wireless Standard,48th International Symposium ELMAR-2006, Croatia, June 07-09, 2006, pp. 259-262
  • [9] V. A. Rani; S. A. James; J. A. Sneha; B. Joe S (2015), PLC based process control automation using gsm and SCADA technology,International Journal of Pharmacy & Technology, vol. 7, no. 2, pp. 9243-9251, 2015